LM12U Lamp Module 3-pin

Control/dim any incandescent (normal bulb) lamp 40w to 300w (240VAC). Simply plug into to any wall socket like an ordinary plug, set the ID code using the front dials and that's it. Unit accepts standard X-10 codes including 'All lights on/off'.
No installation required

LM15 'Bayonet' Lamp Module

Control any lamp up to 100w (230VAC). ON/OFF Only. Does not respond to Dim/Bright.
No installation required

AM12U Appliance Module 3-pin

Control any Appliance up to 13 Amp (240VAC). Simply plug into to any wall socket like an ordinary plug, set the ID code using the front dials and that's it. Unit accepts standard X-10 codes including 'All units off'.
No installation required

LW10 Wall Dimmer Switch Module

Replacement Wallswitch for switching and dimming incandescent lights up to 300w (240VAC). Simply push to dim or push and hold to dim to the required level. Unit accepts standard X-10 codes including 'All lights on/off'.
Installation required

AW10 Appliance Wall-Switch Module

Switch any light/appliance ON or OFF up to 10 Amps load (240VAC). Replaces an existing switch for lights, fans, heaters etc. Unit accepts standard X-10 codes including 'All units off'.
Installation required

LD11 DIN Dimmer Module

Control any lamp 60w to 700w from X-10 code or a momentary rocker switch attached to terminal 1. Mounts on the DIN rail of the mains distribution box or can be installed in sub-junction boxes for discrete control. Unit accepts standard X-10 codes including 'All lights on/off'. Unit also responds to professional X-10 for instant or progressive dimming.
Installation required

AD10U Appliance Module 13A

Control lighting/appliance circuits up to 16 Amps from either latched or 'push to make' wall switchs (240VAC). Mounts on the DIN rail of the mains distribution box or can be installed in sub-junction boxes for discrete control. Unit accepts standard X-10 codes including 'All units off'.
Installation required

XM10E Comfort X10 Interface

The TW7223 is a two-way X-10 interface Module utilised by controller manufacturers to interface their equipment. It will connect directly to the mains terminals within the Comfort Main Control Panel allowing Comfort to send and receive X10 signals around the house.
Installation required

TM13 Transceiver Module

Converts X10 (433MHz) Radio signals into X10 power line signals (240VAC). Plugs into any wall socket. Accepts signals from UR24, HR10, SS13, MS13, KR19,KR22 set to the appropriate house code.
No installation required

UR24 Radio/IR Remote

Emits both RF and Infra Red, so it can be used to operate X-10 devices and also replace up to 8 remotes (i.e. TV, VCR, Sat, DVD, Hi-Fi etc.) Extensive library of built in codes and also has a learning function to learn from your existing remote. (Requires TM13).
No installation required

HR10 16 Channel Radio Remote 433mhz

Sends RF signals to a TM13U. Control any 16 X10 devices, lights and appliances, including Dim/Bright. Handy to have by the side of the chair or bed.
No installation required

SS13 Radio Wallswitch

A wireless wall switch that will control any three X10 devices. Inc Dim/Bright. (Requires TM13U)
No installation required

MS13 Occupancy Sensor

Switch an X10 light or appliance via movement. It will also switch the light off after a user defined, predetermined time of1,2,4,8,16,32,64 or128 minutes. It also has a light sensor so it can be set to only switch when dark. (Requires TM13U).
Installation required

KR19 Radio Remote

A key fob used to control any two X10 devices. Inc Dim/Bright. Can be used inside or out. (Requires TM13U)
No installation required

KR22 Radio Remote

Control any four X10 devices. Inc Dim/Bright (433Mhz). (Requires TM13U)
No installation required

MT10U Mini Timer - Alarm Clock - 230v

Timer controls four light or appliance modules turning each one on/off up to twice a day. Instant switching for 8 modules. Ideal for the bedside with LED clock, alarm buzzer and sleep function.
No installation required

Infrared to X10 - IR543

One Housecode Version
Use the UR24 or Pronto remote to control up to 16 X10-compatible devices with the IR X10 Command Console. It responds to infrared signals and can transmit X10 codes along the 230V ring main wiring. The modules can be either switched on/off or in the case of lights, dimmed and brightened. There is also the facility to switch everything on or off from the built-in buttons. Supplied with 3-PIN UK-Plug(Non-CE) Colour - Black
No installation required

Infrared to X10 - IR543AH

All Housecodes Version
Use the Pronto remote to control the full 256 X10 codes and compatible devices with the IR X10 Command Console. It responds to infrared signals from Philips Pronto and can transmit X10 codes along the 230V ring main wiring. The modules can be either switched on/off or in the case of lights, dimmed and brightened. There is also the facility to switch everything on or off from the built-in buttons. Supplied with 3-PIN UK-Plug and Pronto .ccf file on floppy disk. (Non-CE) Colour - Black
No installation required

CM12U PC Home Manager Kit

Home Manager (alias ActiveHome) is the low cost powerful home automation system controlling lights and appliances from your PC!(Requires 2 x AAA Batteries for backup).

FD10 X10 Filter / Blocker

Ideally should be fitted to all X-10 installations. Prevents X-10 signals entering and exiting a property. Installed at the fuse/breaker box. Essential on all installations where neighbours use X10 products. Connects in series with main incoming live, 63A Max load current.
Installation required

Use the TF678 when you require a large filter (200 amps) or when you want to couple X10 across a 3 phase system.
Installation required

UM506 Universal Module

Contains an isolated contact relay rated at 5A 24VDC. Can be operated as a sound beeper only, contact relay only or both. Contacts and sound can be set to be either continous or momentary. Connected to the mains via a fly lead.
Installation required

You can use XCAM2 to work with Comfort and the Comfort Web Interface. Use your 'wired' PIR responses to send the X10 signal along the mains wiring to select the relevent camera. Only one camera is viewed at one time, which is perfect for CWI..

XCAM Wireless COLOUR Camera - 230v

This wireless COLOUR camera may be added to the XCAM2 providing additional cameras controlled from the same 2.4GHz receiver connected to your VCR. Each additional Camera requires 230v mains supply. UK PLUG TYPE ONLY. MAX of 4 cameras may be used.

XCAM2 Wireless COLOUR Camera - 230v

Wireless camera with built in transmitter and seperate wireless receiver. UK PLUG TYPE ONLY. MAX of 4 cameras may be used.

XCAM2 PIR Wireless COLOUR Camera - 230v

XCAM2 as above with PIR attached, receiver unit and also a VCR commander which can be programmed to emit VCR commands. UK PLUG TYPE ONLY. MAX of 4 cameras may be used.

XCAM2 3 Camera Kit- 230v

XCAM2 as above with 2 additional cameras, 1 transceiver module (TM13U) and 1 wireless transmitter/dimmer (HR10E). UK PLUG TYPE ONLY. MAX of 4 cameras may be used.

ZC15A Kit Pan 'n' Tilt

Pan 'n' Tilt for the XCAM2 camera system. Comes with remote control

Powermid XL 433Mhz Remote IR Sender (240VAC)

Easily change channels from any room in your home! The Wireless RemoteSENDER is the missing link in your home. Have you ever wished your infrared remote control could transmit through walls? Now it can. Simply place the transmitter in another room and place the receiver anywhere in the room where the equipment you want to control is located. The transmitter receives the infrared (IR) signals from your remote control and converts them into a radio frequency signal. This signal penetrates walls and is picked up by the Receiver. The receiver then converts the signal back into an IR signal and sends the command to the equipment being controlled.

MK Wall Switches

These hi-quality 20AMP wallswitches are manufactured by MK and are ideal for use with the LD10 and AD10 DIN Rail units. The metal yoke design allows you to mix momentary push-to-make (PTM) switches with normal make-break(MB) types. Single gang momentary is also available (WS-SGL-PTM).
Installation required